> Knowledge base> Category: Bravo I
Search
Share
Category: Bravo I
124 Articles
Orange arrow Can I operate my Bravo with its cover open?

9759 views
  Can I operate my Bravo with its cover open? No. The cover must be closed for the robotics to move. This is a required safety feature. However, there is a way to open the lid and watch the Bravo if you need to observe the robotic movements for troubleshooting purposes. You can simply block the opt...
Orange arrow The arm for my Bravo / Bravo II / Bravo Pro is stuck in the up or down position. It makes a buzzing noise when I power on the unit. (inhouse)

7665 views
  The arm for my Bravo / Bravo II / Bravo Pro is stuck in the up or down position. It makes a buzzing noise when I power on the unit. Bravo II This can happen if the Bravo II power is interrupted during an arm movement. Use the following procedure to correct the problem. 1. Power off the unit.2....
Orange arrow The arm and cartridges slam into the sides or move in fast jerking motions back and forth. (Bravo/BravoPro/Signature)

7074 views
  The arm and cartridges slam into the sides or move in fast jerking motions back and forth. The encoder belt may have slipped out of its track in the back of the head carriage unit or may have become unseated from the posts on either side of the unit. The printhead carriage has a sensor behind it...
Orange arrow Can I span data over multiple discs so that I can use my duplicator as a back up device? (Windows Only)

7411 views
  Can I span data over multiple discs so that I can use my duplicator as a back up device? (Windows Only) It is NOT possible to span data over the multiple discs using the Primo DVD software. You can back up data but you will need to determine where to end one set of data and begin another on multip...
Orange arrow The image is printing off center on my disc every few prints. It will print several centered and then one off center and then go back to centered again. (Bravo)

5392 views
  The image is printing off center on my disc every few prints. It will print several centered and then one off center and then go back to centered again. (Bravo) This can happen because of a dirty encoder belt on the Bravo. The encoder belt runs the entire width of the Bravo and is parallel to the...
Orange arrow What is the difference between DVD+R and DVD-R?

11039 views
  What is the difference between DVD+R and DVD-R? The practical difference between +R and -R discs is that some +R discs play on players that -R disc don't play on and vice versa. The technical differences are numerous. The main difference is that DVD+R use ADIP format to write instead of Pre-pits...
Orange arrow "The duplicator cover is open. Shut the top cover to continue" Received this error but the cover IS closed.

5435 views
  "The duplicator cover is open. Shut the top cover to continue" Received this error but the cover IS closed. The reflective sticker on the tinted cover may have come off or is out of place. If you open the lid and look where it hinges to the Bravo on the right side you should see reflective tape...
Orange arrow How many discs per cartridge can the Bravo/Bravo II print?

6799 views
  How many discs per cartridge can the Bravo/Bravo II print? This depends on many factors. However, with 100% coverage and printing an even amount of each color at the default resolution of 1200 the Bravo/Bravo II prints approximately 100 to 130 discs per cartridge. If you are not printing full cove...
Orange arrow What is the size capacity of my DVD, Dual Layer DVD or Blu-ray disc?

22413 views
  DVD and Blu-ray manufacturers state capacity in decimal form. However, most computers read capacity in binary. The following table translates stated decimal capacity into actual binary capacity. Single layer capacity Dual/Double layer capacity Stated Capacity (GB) PTPublisher Capa...
Orange arrow How do I prepare my unit for shipping to Primera for repair or exchange?

13552 views
  How do I prepare my unit for shipping to Primera for repair or exchange? The instructions below should be followed for each product before boxing. It is best to use the original box and foam/cardboard supports. If you do not have the box, package the product in a box large enough to leave space ...
Orange arrow What is the difference between RGB and CMYK Color environments? What are PMS (Spot) colors?

8629 views
  What is the difference between RGB and CMYK Color environments? What are PMS (Spot) colors? “CMYK”, “RGB” Each of these acronyms refers to a method of building colors for different environments. RGB The one that you are perhaps most familiar with (or aware of) is RGB. I...
Orange arrow How do I print my labels all the way to the center or outer edge of the disc?

9275 views
  How do I print my labels all the way to the center or outer edge of the disc? To make the printer print closer to the center you need to adjust the Center Size in the driver preferences. Go to the Start Menu - Control Panel - Printers - Right click on the Disc Publisher/CD Color Printer 6 and cho...
Orange arrow How do I find the firmware version of my Primera product? (Mac or PC)

7577 views
  How do I find the firmware version of my Primera product?Finding the Firmware Version on a PC. 1. Go to the Start Menu - Choose Printers and Faxes.2. Right Click on the Printer Driver - Choose Printing Preferences.3. Click on Clean/Change Cartridges & Check Ink... as shown below - Choose Prope...
Orange arrow How do I send my product in for repair? How much is it? Where do I send it?

33763 views
  Please contact technical support via phone, email or chat before sending your product in for repair. If they determine that the product needs repair, they will send you a Return Material Authorization (RMA) document which includes the RMA number, packing instructions and the shipping address of our...
Orange arrow The ink in the color cartridge is mixing or the first few passes of printing are lighter than the rest. (Cleaning the Maintenance Station)

10850 views
  The ink in the color cartridge is mixing or the first few passes of printing are lighter than the rest. (Cleaning the Maintenance Station) Cleaning the maintenance station prevents the color ink cartridge from mixing or the first few printing passes from being lighter than the rest of the label...

Page: 1 of 9
©2024 Primera   |   powered by LiveHelpNow Help Desk Software
 Total articles: 640 | Total views: 4198376