> Knowledge base> Category: Bravo Pro-XRP-Xi Series
Category: Bravo Pro-XRP-Xi Series
233 Articles
Orange arrow “A robot was found but no drive was found” error when opening PTPublisher on Mac.

5182 views
  “A robot was found but no drive was found” error when opening PTPublisher on Mac. Typically, this means the drive in the Bravo is not being recognized by the Mac. Go to Apple – About this Mac – More Info – Hardware - Disc Burning. You should see an extra CD...
Orange arrow The arm and cartridges slam into the sides of the unit or move in fast jerking motions back and forth. (Bravo/BravoPro/Signature)

7335 views
  The arm and cartridges slam into the sides of the unit or move in fast jerking motions back and forth. The encoder belt may have slipped out of its track in the back of the head carriage unit or it may have become unseated from the posts on either side of the unit. The print head carriage has a ...
Orange arrow How to Disable Driver Signature Enforcement in Windows 8.

4187 views
  How to Disable Driver Signature Enforcement in Windows 8. From the Metro Start Screen, open Settings (move your mouse to the bottom-right-corner of the screen and wait for the pop-out bar to appear, then click the Gear icon). Click ‘Change PC Settings’. Click ‘General’....
Orange arrow What specific rights are required in the Windows registry?

3332 views
  What specific rights are required in the Windows registry? Check permissions on two folders in the registry. To access the registry, go to Start – Run on Windows XP or click the Start (Windows logo) - All Programs - Accessories - Run on Windows Vista and Windows 7. Type in regedit and cl...
Orange arrow Unable to change the inner diameter or outer margin of the printed disc. (PTPublisher Mac)

3024 views
  Unable to change the inner diameter or outer margin of the printed disc. (PTPublisher Mac) 1. Make sure the image you are printing does not already have the inner diameter or outer margin built into the image. Some designers add the cropped inner circle and outer margin into the design using thei...
Orange arrow The arm for my Bravo / Bravo II / Bravo Pro is stuck in the up or down position. It makes a buzzing noise when I power on the unit. (inhouse)

2442 views
  The arm for my Bravo / Bravo II / Bravo Pro is stuck in the up or down position. It makes a buzzing noise when I power on the unit. Bravo II This can happen if the Bravo II power is interrupted during an arm movement. Use the following procedure to correct the problem. 1. Power off the unit.2....
Orange arrow Continuous alternating fast flashing lights appear when the unit is powered on. (BravoPro-XRP)

2110 views
  Continuous alternating fast flashing lights appear when the unit is powered on. You may have a defective cartridge. Try the following:1. Remove both the color and the black cartridge. 2. Power off the unit.3. Power on the unit with no cartridges installed.4. The unit should initialize by displayin...
Orange arrow "The duplicator cover is open. Shut the top cover to continue" Received this error but the cover IS closed.

1325 views
  "The duplicator cover is open. Shut the top cover to continue" Received this error but the cover IS closed. The reflective sticker on the tinted cover may have come off or is out of place. If you open the lid and look where it hinges to the Bravo on the right side you should see reflective tape...
Orange arrow What rights or permissions are required for Primera Printers? Can I print from a user (non-admin) account?

4290 views
  To print from a user (non-admin) account, grant the rights below. For any Primera printer follow these steps. 1. Printer Rights. After installing the Printer driver, the administrator must open the Printers Folder, right-click on Primera Printer and click Properties. Click on the Se...
Orange arrow Error - multiple discs have been placed in the recorder or printer but they were not - Problems picking last disc from bin - It says it is empty but it is not - After the last disc is picked, a flash

5353 views
  For BravoPro Xi, 4100 or 4200 Series Only: 1. In PTPublisher, Go to the Tools Menu - Calibrate the Disc Publisher. (For Mac: Go to the PTPublisher Menu - Calibrate Robot)2. Find the "Other Calibrations" section at the bottom.3. If the error occurred after the disc was placed in the printer, click ...
Orange arrow I receive the error when printing from PTPublisher 'No compatible devices found, would you like to print on plain paper?' (PTPublisher)

2685 views
  I receive the error when printing from PTPublisher 'No compatible devices found, would you like to print on plain paper?' (PTPublisher) There are three possible reasons this error occurs: 1. More than one version of SureThing is installed on the computer. Check to make sure only one version o...
Orange arrow I would like to print a serial number, print date/time, or personalized information on discs - Each disc that is printed will have different information - How do I use SureThing merge fields?

2305 views
  I would like to print a serial number, print date/time, or personalized information on discs - Each disc that is printed will have different information - How do I use SureThing merge fields? With the Insert Field function of the SureThing CD Labeler software you can create serialized discs, autom...
Orange arrow How do I download and use the PT Calibration Utility?

2392 views
  How do I download and use the PT Calibration Utility? If you are having picking or dropping problems please check this article first or check with tech support since these problems can sometimes be caused by things other than a miscalibrated unit. PT Calibration Utility version 1.4.2 ...
Orange arrow How do I find the firmware version of my Primera product? (Mac or PC)

2511 views
  How do I find the firmware version of my Primera product?Finding the Firmware Version on a PC. 1. Go to the Start Menu - Choose Printers and Faxes.2. Right Click on the Printer Driver - Choose Printing Preferences.3. Click on Clean/Change Cartridges & Check Ink... as shown below - Choose Prope...
Orange arrow Discs are printing with poor quality or poor color matching, streaks, banding, or missing colors. (BravoPro or XRP Only)

2779 views
  Discs are printing with poor quality or poor color matching, streaks, banding, or missing colors. (BravoPro or XRP Only) Four print settings affect print quality and color matching on a Bravo Pro or XRP: Print Quality, Disc Surface Quality, Ink Cartridge, and Color Matching. Using various combi...

Page: 1 of 16